Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
Right here down the page you'll find a bunch of very good insight involving Installing A Bathtub.
Setting up a tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the project can relocate immediately; if you need to open up a wall to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either case, the job is within a residence handyman's abilities, although you will require a helper to leave the old tub and embeded in the brand-new one. Make certain you have actually qualified yourself for the job as well as are comfortable attempting it. Instead of employing a service provider to take over a halfway-completed job, it is much better to think about utilizing one prior to you start. Possibilities are you may need a specialist plumber to make tube connections.
This short article will certainly help you install a new bathtub in your shower room if you have actually currently bought a new bathtub and don't need to alter the plan of your previous water pipes.
Your devices and product list ought to make up the following:
Getting ready for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last placement.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, activate the taps to drain any type of water staying in the system. The process of removing the existing taps can be quite problematic because of the limited access that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning throughout this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Bath tub
Making use of both wooden boards under its feet, place the tub in the required placement. The wood boards are handy in equally spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little points.
The following goal is to ensure that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub up until the level reads degree.
To mount taps, fit all-time low of the furthest flexible faucet port to the ideal supply pipe by making a compression join; after that do the very same for the other faucet.
Turn on the water system as well as inspect all joints and brand-new pipework for leakages and tighten them if required. Fill the bath tub and additionally inspect the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub should wait until the tub has actually been made use of at least once as this will resolve it right into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting opening in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Secure the faucet in place with the manufacturer provided backnut. When the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet ports. The former type needs to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, causing the water to pass through the wall in between the bathroom and the tiling, causing complications with moisture and also feasible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes and cartridges, and also are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched paper or soft rope. Remember to constantly load the bathtub with water before sealing, to permit the motion experienced when the tub is in usage. The sealant can fracture relatively very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently offered on the marketplace. It is advisable to fit the tiles making use of water-resistant or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Give feedback down the page. We would be delighted to find out your thinking about this write up. Hoping to see you back again soon. I beg you take the opportunity to promote this write-up if you enjoyed reading it. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.
Leading emergency plumbing services available. Report this page